The TZ32V unit is an extremely flexible 32×32 video matrix, programmable directly from the customer.
It is programmable as a matrix in the configurations: CVBS (32×32), Y/C (16×16), YCbCr (10×10), RGBS (8×8).
The TZ32V could be uniform in two lists separate matrices: 2xCVBS (16×16) or 1xCVBS (16×16) + 1xY/C (8×8) or 1xYCbCr (5×5) + 1xY/C (8×8) etc.
It can work in single mode or as a master when connected to the TZ32A audio matrix.
The TZ32V can be commanded through the integrated keyboardoard, from computer with RS232 or RS485 interface and IR control.
Technical Specifications
Technical Specifications TZ32V | |
---|---|
Input type | AC coupled |
Input return loss | >40 dB at 5 MHz |
Output return loss | >40 dB at 5 MHz |
Frequency response | -0.1 dB at 10 MHz; |
-1 dB at 60 MHz; | |
-3 dB at 170 MHz | |
-3 dB One All, worst case, 150 MHz | |
Differential gain | ±0.3% |
Differential phase | ±0.2° |
Crosstalk (worst case) | better than 40 dB at 5 MHz |
Hum & Noise | -80 dB unweighted |
Remote control | IR, RS232, RS485 linkable with TZ32A |
**** | |
Mains input | 230 VAC / 115 VAC (selectable) |
Power consumption | 10 VA |
Size (WxDxH) | 483x130x176 mm |
Weight | 6 kg |
Operating temperature range | 0÷45°C |
Safety | according to EN60065 |
EMC | according to EN55103-1 and-2 |
- Video inputs wth BNC in loop
- Video only, Audio only, AFV (if connected to TZ32A)
- Switching in the frame interval
- Keypad programmable preview output
- CV or Y/C or Y Cb Cr or RGBS
- 12 presets can be recalled
- Mapping capability
- IR remote control (optional)
Brochure / leaflet for TZ32V:
Elpro_TZ32V.pdf
USER MANUAL:
User Instruction Manual for Elpro TZ32V
Elpro_TZ32V_user_manual_eng.pdf
CE CERTIFICATION:
CE Conformity document for TZ32V
CE Conformity
DOCUMENTATION FILES
How to control TZ32 by CNS1000
CNS1000_conn_TZ32_eng.pdf
WINDOWS DRIVERS
Control Software for TZ32V and TZ32A
TZ32_driver_1_0_b_4.zip
Available Software:
Software to upload firmware into Elpro units
Elpro_uploader.zip
FIRMWARE
Firmware updating of the Elpro devices is possible using the specific utility UPLOADER.
This software should be downloaded and installed on a PC in a Windows environment.
To perform the updating of the firmware it is necessary to connect the device to the PC serial line and therefore to perform the action (typical for every device) to put the device in UPGRADE MODE.
Then load the .hex file of the new firmware version and start uploading to the device.
At the conclusion of the updating it is necessary to turn OFF and ON again the device.
How to set the TZ32V
in UPGRADE MODE
Turn the TZ32V ON holding the key 3 pressed.
The UPGRADE MODE is signaled by message “ELPRO VIDEO LABS — Update Firmware”.
Notes: Memorization on non-volatile memory of the Video connections.
Current release: 1.3
MD5: A0C83889652E6B1E2D52D3E23FCC92C6
Elpro_FW_TZ32Vr13.zip
High Resolution Images
Download here the available Hi-Res images of TZ32V.