DVIPRO1000 is a scaler/matrix switcher 8×2 that transforms the incoming video and PC inputs in 2 independent outputs both with RGBHV and DVI simultaneous signals.
DVIPRO1000 has 8 universal video inputs HDTV compatible.
Through the best Faroudja and DCDi technology, it’s possible to set several parameters to change the image quality and the video effects.
Besides the Scaler function, the DVIPRO1000 provides the PIP (Picture in Picture)between 2 different sources.
Both the output images can be scaled separately pixel by pixel and moved in X and Y position on the screen (PAN).
The text and image overlay permit a complete and useful titling function.
The large number of features and the presence of the combined audio to each input, makes the DVIPRO1000 very useful in the presentation systems where several sources must be displayed onto 2 different destiantions, such a local monitor for preview and a videoprojector for displaying program.
|Inputs||N°2 universal CV, Y/C, YPbPr,RGBHVon HDD 15p.f.|
|N°4 universal CV, Y/C,YPbPr,RGBHV on 3 BNC and 1 15 p.f.|
|N°1 universal CV, Y/C, YPbPr, HDMI on 3 BNC and 1 HDMI connector|
|Graphic||SVGA, XGA, WXGA, SXGA, SXGA+, WSXGA, WSXGA+, UXGA|
|RGBHV||720p, 1080i, 1080p|
|Input formats||PAL, SECAM, NTSC|
|Outputs||N°2 separated, PW function on OUT1|
|Output type||twin, DVI-D on DVI 29 p.f. and graphic + YPbPr on HDD 15p.f.|
|Vertical sync||60 Hz|
|PIP||between 2 inputs|
|UpScale & DownScale pixel x xpixel|
|Pan on both images in X and Y|
|Function||image adj. overlay, DNR, motion control|
|Inputs/outputs type||N° 8 balanced with Phoenix screwtype, removable|
|Input impedance||56 KΩ|
|Input level||+9Dbm Max|
|SPDIF out||for HDMI input only|
|VCA on outputs||from MUTE to 100% (33 steps)|
|Frequency response||-1dB from 40 Hz to 20 KHz|
|Crosstalk||60 dB at 5 KHz|
|Hum & noise||-75 dBm unweighted|
|Outputs||N°1 unbalanced, 150 Ω RCA outlet|
|N° 1 balanced 600 Ω with Phoenix screwtype|
|Remote command||IR, RS232, LAN|
|Main input||90-240 Vac 50-60 Hz|
|Power consumption||25 VA|
|Size (WxDxH)||483x210x132 mm|
|Operating temp. range||0-45 °C|
|Safety||accordig to EN60065|
|EMC||according to EN55103-1 and -2|
- Outputs resolution up to 1600×1200 and 1080p
- 10 bit ADC sampling resolution
- Faroudja and DCDi technology
- ‘Seamless’switching with fading
- 8 separate universal inputs with combined audio
- 2 independent outputs
- Setup saving and recalling
- Full PIP function
- Pixel x Pixel Upscale and Downscale of images
- Pan of images in PIP
- Text or image overlay
- IR control provided
- Controlled by IR, RS232 and LAN
- Audio output level control
Brochure / leaflet for DVIPRO1000:
Instructions manual for DVIPRO1000
CE Conformity document for DVIPRO1000
User manual for LAN202
Control Software for DVIPRO100, DVIPRO1000, DVIDEC100 and DVISEL403
Software for firmware uploading
Software for Ethernet interface configuration and virtual COM management
Software for Ethernet interface configuration and virtual COM management – Win 32bit
150727 Tibbo tdst-5-09-12-x86-01.zip
Software for Ethernet interface configuration and virtual COM management – Win 64bit
150727 Tibbo tdst-5-09-12-x64-01.zip
Firmware updating of the Elpro devices is possible using the specific utility UPLOADER.
This software should be downloaded and installed on a PC in a Windows environment.
To perform the updating of the firmware it is necessary to connect the device to the PC serial line and therefore to perform the action (typical for every device) to put the device in UPGRADE MODE.
Then load the .hex file of the new firmware version and start uploading to the device.
At the conclusion of the updating it is necessary to turn OFF and ON again the device.
How to set the DVIPRO1000
in UPGRADE MODE
Please, refer to the Instruction Manual
Current release: 1.3
High Resolution Images
Download here the available Hi-Res images of DVIPRO1000.