DVIPRO100 is a unit that transforms the incoming video and PC inputs in a RGBHV and DVI signals.
The two outputs are simultaneous and both present the same resolution.
By IR control or by RS232 it’s possible to change several parameters to adjust the image.
Besides the Scaler function, the DVIPRO100 provides the PIP (Picture in Picture) between a video overlayed into a PC source.
Both can be scaled separately pixel by pixel and moved in X and Y position on the screen (PAN).
The Scaler and PIP features and the presence of the combined audio to each input, makes the DVIPRO100 very useful in the presentation systems where several sources must be displayed onto RGBHV and DVI destinations.
Technical Specifications
VIDEO | |
---|---|
Inputs | N°1 CV; N°1 Y/C |
N°1 CV or YCbCr | |
N°2 Graphic | |
Input formats | PAL, SECAM, NTSC |
Outputs | N°1 DVI-D output |
Outputs | N°1 High resolution with HDD 15 p.f. |
Output Format | Selectable SVGA, XGA, SXGA and HDTV 480p, 576p, 720p, 1080i |
Standards | PAL, SECAM; NTSC |
Synch. Level | TTL |
Vertical synch. | 60 Hz |
PIP | Video on PC |
UpScale & DownScale pixel x pixel | |
Pan of both images in X and Y |
AUDIO | |
---|---|
Inputs | N°5 unbalanced with RCA outlet |
Input coupling | AC |
Input impedance | 56KΩ |
Input level | +9 dBm Max |
VCA on outputs | from MUTE to 100% (33 steps) |
Frequency response | -1 dB from 40 Hz to 20 KHz |
Crosstalk | 60 dB at 5 KHz |
Distortion | |
Hum & Noise | -75 dBm unweighted |
Outputs | N°1 Unbalanced, 150Ω with RCA outlet |
N°1 Balanced, 600Ω with Phoenix screwtype | |
Remote control | IR, RS232, LAN |
**** | |
Mains inputs | 90÷240 VAC 50-60 Hz |
Power consumption | 15 VA |
Size (WxDxH) | 483x210x44 mm |
Weight | 3 kg |
Operating temperature range | 0÷45°C |
Safety | according to EN 60065 |
EMC | according to EN 55103-1 and EN 55103-2 |
- Outputs resolution up to 1280×1024 and 1080i
- ‘Seamless’switching with fading
- 5 separate inputs with combined audio
- Setup saving and recalling
- PIP: Video on PC
- Pixel x Pixel Upscale and Downscale of images
- Pan of images in PIP
- Optional IR control
- Controlled by RS232
- Audio output level control
- Optional LAN control
Brochure / leaflet for DVIPRO100:
Elpro_DVIPRO100.pdf
USER MANUAL:
User Instruction Manual for Elpro DVIPRO100
Elpro_DVIPRO100_user_manual_eng.pdf
CE CERTIFICATION:
CE Conformity document for DVIPRO100
CE Conformity
DOCUMENTATION FILES
Application notes for DVIPRO100
DVIPRO100_application.pdf
User manual for LAN202
LAN202_note_eng.pdf
WINDOWS DRIVERS
Control Software for DVIPRO100, DVIPRO1000, DVIDEC100 and DVISEL403
DVI_driver_2_3.zip
Available Software:
Software to upload firmware into Elpro units
Elpro_uploader.zip
Software for Ethernet interface configuration and virtual COM management – Win 32bit
150727 Tibbo tdst-5-09-12-x86-01.zip
Software for Ethernet interface configuration and virtual COM management – Win 64bit
150727 Tibbo tdst-5-09-12-x64-01.zip
FIRMWARE
Firmware updating of the Elpro devices is possible using the specific utility UPLOADER.
This software should be downloaded and installed on a PC in a Windows environment.
To perform the updating of the firmware it is necessary to connect the device to the PC serial line and therefore to perform the action (typical for every device) to put the device in UPGRADE MODE.
Then load the .hex file of the new firmware version and start uploading to the device.
At the conclusion of the updating it is necessary to turn OFF and ON again the device.
How to set the DVIPRO100
in UPGRADE MODE
Move the dip-switches 2 and 3 in ON position (rear side), then turn the DVIPRO100 on.
Current release: 1.2
MD5: 4CD9F139AB244D280852AA954CA014BD
Elpro_FW_PRO100_2.zip
High Resolution Images
Download here the available Hi-Res images of DVIPRO100.